Can you make me a toy, or change one of your toys?
The short answer to these questions is "As long as you have a big enough budget."
Yeah, I'm interested, and willing to shell out. What's it take for a brand new toy, like what you have on the shop? Two holes on a butt, or something like that?
Depends on how much work has to be done, if you want all the production materials that went into making it, and what happens to the finished product afterward. The more of that I have to do, the more things you want, and the more limited I am with what I can do with it after the project is done, the more it'll run you.
As an estimate in the scenario of " I have absolutely nothing, I just want you to make me a toy from scratch base don a vague idea that I think is sexy, and I want it made only for me", you're looking at 1,000$ to start with.
No no, I want something BIGGER. Like, a straight up DOLL. With limbs and bones and a skeleton and everything! With big boobies and butts and different materials and-
First, bear in mind you're asking me to try something I have never done successfully before, at a scale that can actually be used as a penetrable toy.
The absolute most I have done in this regard was a small scale clay sculpt with a wire embedded inside of it to act as a skeleton to pose it after it's been silicone cast.
The wires were misaligned, poked out the limbs, and ran the entire length of the toy.

Nothing's going to fit inside that.
Okay maybe not a whole doll, but can you give me something with boobs and a face so it's one piece?
That's more doable, but there are still some caveats and limitations as to what can be done.
Fine details like hair, eyes, lips, and that sort of thing though? Absolutely not happening.

Something like THIS though?

Nope. Not happening.
Can you close the end of the toy so it's just one opening per hole? I want it to be like those flesh colored TPE toys I saw from [ Insert toy shop here ] !
Yes.
But this is a bad idea.
You cannot easily clean a silicone toy of this size the same way by turning it inside out. Too thick and heavy.
Any "Suction" sensation you're probably after is offset by the fact that there's going to be an air pocket you compress by pushing into the now sealed cavity. This does not create a pleasant sensation.
Just cap the end with a finger; the toys are designed specifically so that this is easily done.
Take it from the guy who actually tried it out.
If you absolutely positively 100% need to have a sealed end toy, I strongly recommend just grabbing a mass produced TPE toy instead of asking me to seal the end, or plugging the end with like a PVC pipe end / flat piece of plastic or something.
This is how much I REALLY do not recommend doing this.
But I'll do it if you're insistent.
It's going to be after the toy is fully cured and extracted, which means the plugged end is not guaranteed to stay sealed, especially with the air you're pushing against it during the expected mechanical stresses the toy will experience, but I'll do it for an additional fee.
What if I just want a different texture for the channel(s) ?
This, I can help you with.
I will still be making your textured channel from scratch, from the digital sculpt, to the print, and the post processing.
This can be expected to be about 2-3 days worth of extra lead time, and an additional 50$ at a minimum per channel.
If you'd like to go for this, and have a solid idea in mind, throw me a message.
How about changing your toy? Can you make me X, but with Y bigger / smaller / a different shape / different genitals / tighter hole/ looser hole ????
"Changes" on this level require all the same effort of an entirely new toy.
So, yes, but you're basically asking me to make a toy from scratch. See above.
Male versions of toys?
I'm not personally interested in making anything male themed.
The only thing I've made in that vein is this attachment for the ponut to simulate a scrotum, because people would not stop asking. So I put in the work to show exactly what is involved in this "Simple change".


It has to be made in the same batch as the toy in question, has to be custom fit PER toy type, which isn't guranteed to even work in a convincing manner, and requires some fiddling to be made pourable. There's always going to be some kind of gap making the two objects not flush with one another.
This is no small amount of work for something I am not personally interested in making; much less for everything I have.
So, in most cases, the answer is no.
BIGGER versions of toys??
Sure, if you have about 1,000$ and don't mind the finish being less than perfect. Throw me a message.
Otherwise, no.
The entire process for larger toys is wildly impractical without either personal motivation, or someone paying me.